Ports

IMG_2886
IMG_2889To begin making the ports I started with creating a stencil out of styrofoam. I used two one quart cans side by side to get the rounded edges and then just drew lines between them to get the shape.  Then cut out enough for all the ports.

IMG_2887IMG_2888Then I drew an outline of were I wanted the ports to line up prior to cutting into the cabin walls.

IMG_2901

IMG_2903Then all the portholes were cut.

IMG_2902
IMG_2906Notice I added two extra portholes in the front for better visibility from inside.

IMG_2907IMG_2908All the porthole rings cut and stained and all the plexiglass marked for cutting.

*Note* Plexiglass was too brittle and cracked easy, so I changed it out for Lexan.  Cost a little more but was easier to cut and much stronger.

IMG_3075You may have noticed in the above picture that there are more porthole rings than portholes. This is because I am making opening windows with an outside screen.

IMG_3081IMG_3080The porthole windows installed with nice brass locking fixtures.

Unfortunately the two forward portholes are too curved to make functional opening windows, so they will remain fixed ports.

Hatch Box

IMG_2846 IMG_2847Side walls are measured and cut, with stringers attached.

IMG_2848 IMG_2849Stringers all attached with glue in place, then everything is screwed together.

IMG_2852IMG_2851Different views with cover in place.  I decided to make the hatch box slightly smaller than the width of the opening, because I plan to use the box for housing the electrical switches and want easy access.

IMG_3106IMG_3102Here are the switches for all the electrical components. There is a matching switch on the opposite side of the box and not pictured is the volt meter, which is mounted in the center of the box just under the lid for easy read access.

Cockpit Seats

IMG_2776Installing the cockpit seats begins with stringers and the side walls of the seats.

IMG_2775IMG_2777Here is a head on shot of the side walls.  After setting these in place I decided there was too little foot room at the back of the boat so I decided to look for a different option.  After digging through the internet and checking out some of the builders blogs I found two different Weekenders “Molly” and “Spiritwind” that had great ideas for seating.  Sooo, I put my engineering and analytical skills to the test and build my seats with no guide other than these examples.  I did however keep notes and if anyone is interested, I will be glad to share them.

IMG_2821First I made a styrofoam cutout of what I wanted the seats to look like.  This included a side wall, back wall and top/seat.

IMG_2820IMG_2819

IMG_2825Stringers are fabricated and placed into position.

IMG_2829IMG_2832Seat components are fabricated.

IMG_2833IMG_2831The seat box is attached to the stringers, then the seats placed on top.

IMG_2838IMG_2839The seat backs are installed. This was tricky at the forward end of the seat back because of a step off between the seat back stringer and the deck. Despite the difficulty, it turned out really cool!

IMG_2840IMG_2841Completed seats and seat backs. I originally designed this for extra leg and foot room, as well as room for a cooler, picnic basket or even other supplies.

IMG_3062IMG_3063Custom built removable bench seats.

IMG_3064IMG_3065IMG_3070

IMG_3069IMG_3071Finished seats before staining.

Cabin

IMG_2714IMG_2713Cabin construction starts with stringers installed along the underside of the deck opening and the cabin wall is attached. Stringers are also attached to the inside of the cabin wall for placement of the cabin roof.

IMG_2715IMG_2716Rafters were previous cut, stained and varnished, along with custom bases, then all were installed.

IMG_2720IMG_2722The cabin roof installation was fun to glue and screw down. I started in the center and worked outward, sitting on the roof itself and would slide outward with every screw placement.

IMG_2721IMG_2718The plan warns that there will be a small shortage, and to adjust for this, you will need a small triangle of plywood as a filler.

IMG_2727View of the inside of the cabin walls and hull side. You can see all the stringers and the custom rafter bases. The stringers were all cut in curves out of scrap stock. This was much easier that trying to bend them into place.

Bowsprit

IMG_2701IMG_2705Test fit of Bowsprit.

IMG_2693To make the end of the bowsprit rounded, I used a hammer and chisel to get the rough shape. Then used a belt sander to finish out the shape, and fine tuned it by hand sanding.

Mast Box

IMG_2658Placement of the mast box will be in the gap between the stringers in front of the forward bulkhead. This will make a nice tight fit for the box.

IMG_2660IMG_2659Here is how it is supposed to look when finished.

IMG_2686Well when I went to cut the opening in the deck for the mast, I was off center by nearly a 1/2″, so I had make some modifications. To make a long story short, I took out the side wall in the direction I needed to shift the box for it to be center, and then filled in the opposite side with the appropriate thickness of plywood.

IMG_2688IMG_2687Then I reattached the side wall I removed and added a little more reinforcement just in case. Overkill I know, but trust me…that mast is not going anywhere!

Rub Rails

IMG_2758IMG_2759Port and Starboard Rub rails completed.

IMG_2762IMG_2761

IMG_2763IMG_2764

IMG_2765Installing the rub rails did require the help of an extra pair of hands.  The rails are made up of 1×2 trim that are 16′ long.  I first used the board itself as a guide to mark a line on top and bottom of the rail against the hull side.  Unfortunately I did not take any pictures of this process.

Next I routed off the top side of each rail with a 1/2″ bit and the bottom side with a 1/4 ” bit.  Then installing the lower rail first, I was able to drill pilot holes through the hull sides between the guide lines, then come back to glue and screw the rails into place.  I did this with the bottom rub rails only because there was not enough room on the inside to do the same on the top rails.  When installing the top rails I made sure to raise the rub rail a 1/2″ above the deck surface so I could then apply a length of 1/2″ round to the inside edge of the top rub rail with glue and ring nails.  This gives the top rub rail a nice round finish.